The diagram shows a bimetallic strip used as a thermostat in a circuit. Copper expands more than Invar for the same temperature rise.

What will be switched on when the bimetallic strip becomes hot?

1.	bell only	2.	lamp and bell only
3.	motor and bell only	4.	lamp, bell, and motor

A piece of iron is heated in a flame. If it becomes dull red first, then becomes reddish yellow, and finally turns to white hot, the correct explanation for the above observation is possible by using:

In an experiment on the specific heat of a metal, a \(0.20~\text{kg}\) block of the metal at \(150^{\circ}\text{C}\) is dropped in a copper calorimeter (of water equivalent of \(0.025~\text{kg}\)) containing \(150~\text{cm}^{3}\) of water at \(27^{\circ}\text{C}.\) The final temperature is \(40^{\circ}\text{C}.\) The specific heat of the metal will be: 
(the heat losses to the surroundings are negligible)
1. \(0 . 40  ~ \text{Jg}^{- 1} \text{K}^{- 1}\)
2. \(0 . 43  ~ \text{Jg}^{- 1} \text{K}^{- 1}\)
3. \(0 . 54 ~ \text{Jg}^{- 1} \text{K}^{- 1}\)
4. \(0 . 61 ~ \text{Jg}^{- 1} \text{K}^{- 1}\)

A brass wire \(1.8~\text m\) long at \(27^\circ \text C\) is held taut with a little tension between two rigid supports. If the wire is cooled to a temperature of \(-39^\circ \text C,\) what is the tension created in the wire?
( Assume diameter of the wire to be \(2.0~\text{mm}\) , coefficient of linear expansion of brass \(=2.0 \times10^{-5}~\text{K}^{-1},\) Young's modulus of brass\(=0.91 \times10^{11}~\text{Pa}\) )
1. \(3.8 \times 10^3~\text N\) 
2. \(3.8 \times 10^2~\text N\) 
3. \(2.9 \times 10^{-2}~\text N\) 
4. \(2.9 \times 10^{2}~\text N\) 

\(5 ~\text g\) of water at \(30^{\circ} \text{C}\) and \(5 ~\text g\) of ice at \(-20^{\circ} \text{C}\) are mixed together in a calorimeter. The water equivalent of the calorimeter is negligible, and the specific heat and latent heat of ice are \(0.5~\text{cal/g}^{\circ} \text{C}\) and \(80~\text{cal/g},\) respectively. The final temperature of the mixture is:

Two conducting slabs of heat conductivity \(K_{1} ~\text{and}~K_{2}\) are joined as shown in figure. If the temperature at the ends of the slabs are \(\theta_{1}~\text{and}~\theta_{2} \ (\theta_{1}   >   \theta_{2} ),  \) then the final temperature \( \left(\theta\right)_{m} \) of the junction will be:

Three rods made of the same material, having the same cross-sectional area but different lengths 10 cm, 20 cm and 30 cm are joined as shown. The temperature of the junction will be:-

   
1. \(10.8^{\circ}\mathrm{C}\)
2. \(14.6^{\circ}\mathrm{C}\)
3. \(16.4^{\circ}\mathrm{C}\)
4. \(18.2^{\circ}\mathrm{C}\)

Four rods of the same material with different radii \(r\) and the length \(l\) are used to connect two heat reservoirs at different temperatures. In which of the following cases is the heat conduction fastest?
1. \(r = \frac{1}{3}~\text{cm}, l = \frac{1}{9}~\text{cm}\)
2. \(r =3~\text{cm}, l =9~\text{cm}\)
3. \(r =4~\text{cm}, l =8~\text{cm}\)
4. \(r =1~\text{cm}, l =1~\text{cm}\)