Which of the following combinations should be selected for better tuning of an L-C-R circuit used for communication?

1. $R=20\Omega ,<mspace\; width="1em"></mspace>L=1.5H,C=35<mspace\; width="1em"></mspace>\mu F$

2. $R=25\Omega ,<mspace\; width="1em"></mspace>L=2.5H,C=45<mspace\; width="1em"></mspace>\mu F$

3. $R=15\Omega ,<mspace\; width="1em"></mspace>L=3.5H,C=30<mspace\; width="1em"></mspace>\mu F$

4. $R=25\Omega ,<mspace\; width="1em"></mspace>L=1.5H,C=45<mspace\; width="1em"></mspace>\mu F$

The potential differences across the resistance, capacitance and inductance are \(80\) V, \(40\) V and \(100\) V respectively in an \(LCR\) circuit. What is the power factor of this circuit?
1. \(0.4\)
2. \(0.5\)
3. \(0.8\)
4. \(1.0\)

A small-signal voltage V(t)=V_o sinωt is applied across an ideal capacitor C 

1. over a full cycle, the capacitor C does not consume any energy from the voltage source

2. current I(t) is in phase with voltage V(t)

3. current I(t) leads voltage V(t) by 180°

4. current I(t) lags voltage V(t) by 90°

A resistance 'R' draws power 'P' when connected to an AC source. If an inductance is now placed in series with the resistance, such that the impedance of the circuit becomes 'Z' the power drawn will be:

$1.<mspace\; width="1em"></mspace>P{\left(\frac{R}{Z}\right)}^2$
$2.<mspace\; width="1em"></mspace>P\sqrt{\frac{R}{Z}}$
$3.<mspace\; width="1em"></mspace>P\left(\frac{R}{Z}\right)$
$4.<mspace\; width="1em"></mspace>P$ 


 

A transformer having efficiency of 90% is working on 200 V and 3 kW power supply. If the current in the secondary coil is 6A, the voltage across the secondary coil and the current in the primary coil respectively are
1. 300V,15A
2. 450V,15A
3. 450V,13.5A
4. 600V,15A

The instantaneous values of alternating

current and voltages in a circuit are given

as 

$\mathrm{i}=\frac{1}{\sqrt{2}}\sin \left(100\mathrm{\pi t}\right)<mspace\; width="1em"></mspace>\mathrm{ampere}$
$\mathrm{e}=\frac{1}{\sqrt{2}}\sin (100\mathrm{\pi t}+\mathrm{\pi }/3)<mspace\; width="1em"></mspace>\mathrm{volt}$

The average power in Watts consumed in the

circuit is

1. $\frac{1}{4}$

2. $\frac{\sqrt{3}}{4}$

3. $\frac{1}{2}$ 

4. $\frac{1}{8}$

An \(AC\) voltage is applied to a resistance \(R\) and an inductor \(L\) in series. If \(R\) and the inductive reactance are both equal to \(3~ \Omega, \) then the phase difference between the applied voltage and the current in the circuit will be:

The rms value of potential difference V shown in the figure is

(1) ${\mathrm{V}}_{\mathrm{o}}$                                                     

(2) $\frac{{\mathrm{V}}_{\mathrm{o}}}{\sqrt{2}}$

(3)$\frac{{\mathrm{V}}_{\mathrm{o}}}{2}$                                                     

(4) $\frac{{\mathrm{V}}_{\mathrm{o}}}{\sqrt{3}}$   

A coil has resistance $30<mspace\; width="1em"></mspace>\mathrm{\Omega }$ and inductive reactance $20<mspace\; width="1em"></mspace>\mathrm{\Omega }$ at 50 Hz frequency. If an AC source of 200 V, 100 Hz, is connected across the coil, the current in the coil will be:

 1. $4.0<mspace\; width="1em"></mspace>\mathrm{A}<mspace\; width="1em"></mspace>$                                          

 2. $8.0<mspace\; width="1em"></mspace>\mathrm{A}$

 3. $\frac{20}{\sqrt{13}}\mathrm{A}$                                         

 4. $2.0<mspace\; width="1em"></mspace>\mathrm{A}$