# A student plots a graph from his readings on the determination of Young modulus of a metal wire but forgets to put the labels (figure). The quantities on X and Y-axes may be respectively,                 (a) weight hung and length increased (b) stress applied and length increased (c) stress applied and strain developed (d) length increased and the weight hung Choose the correct option: 1. (a) and (b) 2. (b) and (c) 3. (a), (b) and (d) 4. all of these

Subtopic: Â Young's modulus |
Â 57%
From NCERT
To view explanation, please take trial in the course.
NEET 2025 - Target Batch
Hints
To view explanation, please take trial in the course.
NEET 2025 - Target Batch

The dimension $$[ML^{-1}T^{-2}]$$ can correspond to:

 1 moment of a force 2 surface tension 3 modulus of elasticity 4 coefficient of viscosity
Subtopic: Â Young's modulus |
Â 79%
From NCERT
To view explanation, please take trial in the course.
NEET 2025 - Target Batch
Hints
To view explanation, please take trial in the course.
NEET 2025 - Target Batch

When a metal wire elongates by hanging a load on it, the gravitational potential energy is decreased.

 1 this energy completely appears as the increased kinetic energy of the block 2 this energy completely appears as the increased elastic potential energy of the wire 3 this energy completely appears as heat 4 none of these
Subtopic: Â Potential energy of wire |
From NCERT
To view explanation, please take trial in the course.
NEET 2025 - Target Batch
Hints
To view explanation, please take trial in the course.
NEET 2025 - Target Batch

A heavy mass is attached to a thin wire and is whirled in a vertical circle. The wire is most likely to break:

 1 when the mass is at the highest point 2 when the mass is at the lowest point 3 when the wire is horizontal 4 at an angle of $$\cos^{-1}(\frac{1}{3})$$ from the upward vertical

Subtopic: Â Stress - Strain |
Â 73%
From NCERT
To view explanation, please take trial in the course.
NEET 2025 - Target Batch
Hints
To view explanation, please take trial in the course.
NEET 2025 - Target Batch

The length of a metal wire is $$l_1$$ when the tension in it is $$T_1$$ and is $$l_2$$ when the tension is $$T_2.$$ The natural length of the wire is:
1. $$\frac{l_{1}+l_{2}}{2}$$

2. $$\sqrt{l_{1} l_{2}}$$

3. $$\frac{l_{1} T_{2}-l_{2} T_{1}}{T_{2}-T_{1}}$$

4. $$\frac{l_{1} T_{2}+l_{2} T_{1}}{T_{2}+T_{1}}$$

Subtopic: Â Young's modulus |
Â 66%
From NCERT
To view explanation, please take trial in the course.
NEET 2025 - Target Batch
Hints
To view explanation, please take trial in the course.
NEET 2025 - Target Batch

When a metal wire is stretched by a load, the fractional change in its volume $$\frac{\Delta V}{V}$$ is proportional to:

1. $$\frac{\Delta l}{l}$$

2. $$\left(\frac{\Delta l}{l}\right)^{2}$$

3. $$\sqrt{\Delta l/ l}$$

4. none of these

Subtopic: Â Poisson's Ratio |
Â 56%
From NCERT
To view explanation, please take trial in the course.
NEET 2025 - Target Batch
Hints
To view explanation, please take trial in the course.
NEET 2025 - Target Batch

A heavy uniform rod is hanging vertically from a fixed support. It is stretched by its own weight. The diameter of the rod is:

 1 smallest at the top and gradually increases down the rod. 2 largest at the top and gradually decreases down the rod. 3 uniform everywhere. 4 maximum in the middle.
Subtopic: Â Stress - Strain |
From NCERT
To view explanation, please take trial in the course.
NEET 2025 - Target Batch
Hints
To view explanation, please take trial in the course.
NEET 2025 - Target Batch

A wire elongates by $$1.0$$ mm when a load $$W$$ is hang from it. If this wire goes over a pulley and two weights $$W$$ each are hung at the two ends, the elongation of the wire will be:
1. $$0.5$$ m
2. $$1.0$$ mm
3. $$2.0$$ mm
4. $$4.0$$ mm

Subtopic: Â Young's modulus |
Â 65%
From NCERT
To view explanation, please take trial in the course.
NEET 2025 - Target Batch
Hints
To view explanation, please take trial in the course.
NEET 2025 - Target Batch

Two wires $$A$$ and $$B$$ are made of same material. The wire $$A$$ has a length $$L$$ and diameter $$r$$ while the wire $$B$$ has a length $$2L$$ and diameter $$r/2.$$ If the two wires are stretched by the same force, the elongation in $$A$$ divided by the elongation in $$B$$ is:
1. $$\frac{1}{8}$$
2. $$\frac{1}{4}$$
3. $$4$$
4. $$8$$

Subtopic: Â Young's modulus |
Â 76%
From NCERT
To view explanation, please take trial in the course.
NEET 2025 - Target Batch
Hints
To view explanation, please take trial in the course.
NEET 2025 - Target Batch

A wire can sustain a weight of $$20$$ kg before breaking. If the wire is cut into two equal parts, each part can sustain a weight of:
 1 $$10$$ kg 2 $$20$$ kg 3 $$40$$ kg 4 $$80$$ kg
Subtopic: Â Stress - Strain |
Â 72%
From NCERT
To view explanation, please take trial in the course.
NEET 2025 - Target Batch
Hints
To view explanation, please take trial in the course.
NEET 2025 - Target Batch